Nanocrystalline cores factory supplier by TRANSMART: One of the key factors to the success of TRANSMART is focusing on basic raw materials research and development. Our ability to tailor the composition and specific heat treatments according to our know-how enables us to design alloys with unique properties for specific customer needs. Transmart is one of the few companies worldwide that have mastered the rapid solidification process where alloys are being produced as a thin strip to its final thickness of typically 16 to 30 um. Toroidal transformers from Transmart toroidal transformer manufacturers offer reliable performance and versatility across a wide range of industries requiring precise power conversion solutions. Find many more information on https://www.transmartcore.com/.
On the one hand, it can isolate eddy current, and the data is suitable for higher frequencies; On the other hand, due to the gap effect between particles, the data has low permeability and constant permeability; Because the particle size is small, there is basically no skin phenomenon, and the change of permeability with frequency is relatively stable; Moreover, the powder core can be prepared into special-shaped parts of various shapes for different fields; Finally, the damaged strip in industry can be crushed into magnetic powder, and then made into magnetic powder core, which can reduce the loss and improve the use value of data. The magnetoelectric properties of magnetic particle core mainly depend on the permeability of powder material, size and shape of powder, filling coefficient, content of insulating medium, forming pressure and heat treatment process.
Fe based amorphous alloys are competing with silicon steel in power frequency and medium frequency fields. Compared with silicon steel, iron-based amorphous alloy has the following advantages and disadvantages. The saturated magnetic flux density BS of iron-based amorphous alloy is lower than that of silicon steel. The filling coefficient of Fe based amorphous alloy core is 0.84 ~ 0.86. It shows that Fe based amorphous alloy has better resistance to power waveform distortion than silicon steel.
Transmart amorphous core manufacturer & supplier is mainly engaged in the production and sales of amorphous core materials. The amorphous core transformer is one of Transmart Industrial’s multiple product series.Transmart Industrial’s amorphous C-core is manufactured in strict accordance with relevant national standards. Every detail matters in the production. Strict cost control promotes the production of high-quality and priced-low product. Such a amorphous transformer is up to customers’ needs for a highly cost-effective product.
We know that the actual transformer always works in AC state, and the power loss is not only on the resistance of the coil, but also in the iron core magnetized by alternating current. Usually, the power loss in the iron core is called “iron loss”. The iron loss is caused by two reasons, one is “hysteresis loss” and the other is “eddy current loss”. Nanocrystalline magnetic core is a small part with magnetic conductivity. There are nanocrystalline particles with small particles in the center of nanocrystalline magnetic core. The working principle of nanocrystalline magnetic core is to absorb the common mode current in the cable through the principle of induction heating and convert it into heat to dissipate. rolled silicon steel sheet is selected. It is cut into long pieces according to the size of the required iron core, and then overlapped into “day” shape or “mouth” shape. In principle, in order to reduce eddy current, the thinner the silicon steel sheet, the narrower the spliced strip, and the better the effect. This not only reduces the eddy current loss and temperature rise, but also saves the material of silicon steel sheet. But in fact, when making silicon steel sheet iron core. Not only from the above favorable factors, because making the iron core in that way will greatly increase the working hours and reduce the effective section of the iron core. Therefore, when making transformer iron core with silicon steel sheet, we should start from the specific situation, weigh the advantages and disadvantages and choose the best size. See more information on transmartcore.com.
As the iron core of the transformer, generally 0.35mm thick cold-rolled silicon steel sheet is selected. It is cut into long pieces according to the size of the required iron core, and then overlapped into “day” shape or “mouth” shape. In principle, in order to reduce eddy current, the thinner the silicon steel sheet, the narrower the spliced strip, and the better the effect. This not only reduces the eddy current loss and temperature rise, but also saves the material of silicon steel sheet. But in fact, when making silicon steel sheet iron core. Not only from the above favorable factors, because making the iron core in that way will greatly increase the working hours and reduce the effective section of the iron core. Therefore, when making transformer iron core with silicon steel sheet, we should start from the specific situation, weigh the advantages and disadvantages and choose the best size.